IPC Family

Industrial Packaging Corporation

  • Home
  • Products
    • Corrugated Packaging & Corrugated Pads
    • Honeycomb Pads & Honeycomb Packaging
    • Honeycomb Core
    • Specialty Packaging
    • Kitty Klaws Cat Scratcher
  • IPC University
  • About
  • Contact
  • Employment

Corrugated Pad

Corrugated Pad, Corrugated Pads, Corrugated Cardboard Pads, Angle Pad Non Scruffing Coating

Angle Pad Frame Pad with Non-Scuff Coating

A frame pad can be produced in either angle pads or U-pads. This is a pad that has a minimum of two v-shaped cut-outs, to allow the pad to form around the perimeter of the product being protected. This is typically made to form around two corners but can be made to form around as many as five corners. All other angle pad and u-pad parameters will apply in production specification

Corrugated Angle Pad Super Soft Tissue

Angle Pad Frame Pad with Super-Soft Tissue

Super-Soft is a tissue product laminated by IPC to linerboard. It is primarily used as a non-abrasive coating on our angle pads and u-pads.

Corrugated Straight Angle Pad

Straight Angle Pad

IPC straight angle pad s are produced from A-Flute corrugated. Standard thickness would be 3+ (1/2″), 4+ (3/4″) and 5+ nominal (1″). The standard leg lengths would be 2 1/2″ x 2 1/2″ and our nominal 4″ or 3 3/4″ x 3 3/4″. Leg lengths do NOT need to be the same from one leg to the other. Overall length of the pads can be from 6″ (in a break-away stick of 36″ minimum), to a maximum of 144″. The inside liner can be plain kraft, non-scuff coated or super-soft.

Corrugated Tray Frame Pads

Corrugated Tray with attached Frame Pads

This is a corrugated sheet that has IPC angle frame pads attached to form a tray. This is typically used as protection around casegoods in either a carton or stretch wrapped package. These pads can be adjusted for different thicknesses, to accommodate for size difference from top to bottom.

Corrugated U Shaped Pad

Corrugated U-Pad

The IPC U-Pad is a corrugated protector made in the shape of a U. This pad is also produced from A-Flute corrugated and is typically made in the same thicknesses as the straight angle pad. Minimum center dimension (I.D.) is 3/4″ and minimum leg length is 1 1/2″. The maximum leg length is calculated by combination of thickness and center requirements but can not exceed 6″. Both legs are typically the same lengths but they can be produced with different inside leg lengths. Overall length would be minimum 36″ to maximum of 144″. The inside liner options are the same as the straight angle pad; plain kraft, non-scuff coated or super-soft tissue.

Corrugated Double Walled Scored Glued Pad

Corrugated Double-Walled Scored-Glued Pad

Corrugated A Flute Pad

A-Flute (Close Up)

See A-Flute Build Up video on IPC University page!

Corrugated Flat Pad

Flat Pad

This is a corrugated A-flute flat built-up pad. It is made typically in thicknesses of 3+ (1/2″), 4+ (3/4″), and 5+ nominal (1″). Width of this part, is a minimum of 2″ to a maximum of 10″. Lengths can be minimum of 6″, provided in master length of 36″ to a maximum of 144″. Inside liner on this part can be: plain kraft, non-scuff coating, or Super-soft tissue.

Corrugated Corner Angle Pad

Corner Angle Pad

These can be also be made with U-Pads. The V-shaped cut-out allows it to be folded into a 90 degree corner. Usually, the cut-out is located at the mid-point of the length of the part, to allow the same protection from the corner. If the application requires non-symmetrical protection, the cut-out can be located anywhere along the pad, as long as a minimum of 4 1/2″ is available on the shortest side.

Corrugated Slotted Build Up Block

Slotted Build Up Block

All packaging manufactured by IPC is recyclable. Many of our packaging products are made with paper produced by mills that use recycled fibers. More than half of the paper purchased by IPC for manufacture of our products is made from 100% recycled content.

Request a Quote

Products

  • Corrugated Packaging & Corrugated Pads
  • Honeycomb Pads & Honeycomb Packaging
  • Honeycomb Core
  • Specialty Packaging
  • Kitty Klaws Cat Scratcher

Request a Quote

All IPC products have been made in the USA since the company began in Tomahawk, Wisconsin in 1988!

tomahawk-map1

1515 W Mohawk Dr
PO Box 197
Tomahawk, WI 54487
(715) 453-2223

arcadia-map1

1488 E Halvorsen Ln
Arcadia, WI 54612
(608) 323-3303

fort-payne-map1

1545 Ashley St
Fort Payne, AL 35967
(256) 845-2559

wilton-map1

1500 W 5th St
Wilton, IA 52778
(563) 732-3032

  • Home
  • About
  • Products
  • IPC University
  • Contact
  • Employment
  • Facebook
  • Twitter
  • YouTube

nfib-logo

genelin-trucking-logo.fw

Copyright © 2022 IPC Industrial Packaging Corporation. All Rights Reserved. | Vision Design Group, Inc. | Privacy Policy